How To Install Front License Plate Bracket On Ford Edge

 admin



FLEngineer

Well-Known Member
  1. How To Install Front License Plate Bracket On Ford Edge 2017
  2. How To Install Front License Plate Bracket On Ford Edge Titanium

I-Match Auto Parts Front License Plate Bracket Tag Holder Replacement for 2007-2010 Ford Edge FO1068126 7T4Z17A385AA Black Textured 5.0 out of 5 stars 1 $16.11 $ 16. It does need to be angled to fit, so to avoid any rubbing issues I put a few layers of electrical tape folded across the top and bottom edges of the license plate. This adds grip for it being braced against the front splitter near the bottom, as well as it prevents any scratching issues from the metal edge of the plate. Just picked up my Edge Limited yesterday and removed the front license plate bracket. I drilled the rivets using a 7/32' bit and then purchased 3/8' chrome hole plugs at Lowe's, drilled the holes to 3/8' and put the plugs in.

Joined
Dec 21, 2018
Messages
314
Reaction score
231
Location
Orlando,FL
Vehicle(s)
2019 Ford Ranger Lariat SCrew
Vehicle Showcase
1
Some 2019 Ranger vehicles equipped with a front license plate bracket noted on the loose items check sheet. May exhibit missing instructions for installation at Pre-delivery. Looking at the tag bracket front side, there is an arrow cast into the middle bar; Arrow needs to point up when properly installed. To install, with bracket arrow up, insert the 2 upper brackets (hooks no holes) into the matching slots on the steel bumper, centered 6” below the Ford Oval. Press into position until Hooks are snapped into the slots on both sides, press towards the steel bumper until the lower brackets line up with holes on the bottom of the bumper. Install the screws provided to secure the bracket, torque to 4.8 Nm (43 lb–in).
APPLICABLE VEHICLES
2019 TRUCK: FG P375N RANGER

It’s easy to install the Skene Design license plate bracket. The bracket comes with an installation kit that includes: a drill bit, all the mounting hardware, and a comprehensive installation guide. You’ll provide your own drill and Phillips screwdriver.

How To Install Front License Plate Bracket On Ford Edge 2017

Not sure if you want to install your bracket yourself? Many of our customers prefer to have the bracket installed by an automotive professional: any mechanic or body shop can do it. It takes about 10 minutes.

Video: How to install the Skene Design license plate bracket

Step-by-Step Instructions

This series of photos will guide you through each step of the simple installation process.

Installation Guide

These step-by-step instructions are included with the bracket.

Youtube
  1. Our low profile front license plate bracket comes pre-assembled in two parts – a left side and a right side, as illustrated in the sketches above. Installation is extremely easy, and takes about 10 minutes.
  2. First, measure the distance from the lower edge of your bumper to where you want the top of your license plate to be. Using the included hex key, loosen the front stainless steel button-head cap screw on the left and right brackets. Slide the horizontal section of each bracket so it is this distance from the top end of the vertical brackets. Tighten each front screw, while ensuring that the horizontal brackets are perpendicular with the slot in the vertical section.
  3. With the hex key, attach the right bracket to the right rear side of your license plate, using 2 of the 4 included cap screws and 2 of the 4 included stainless steel trim washers. Do the same for the left bracket with the other 2 screws and washers. Don’t tighten the screws too tightly at this point.
  4. Position the license plate assembly in the desired location on your front bumper. Be sure to center the license plate with your grill. Angle the plate to the desired angle with respect to the bumper by adjusting the angle of the left and right brackets. You may need to slightly loosen the angle adjustment screws. Then note the location where the two horizontal bracket sections contact the underside of the bumper.
  5. Carefully clean the sections on the underside of the bumper you noted in the above step. Alcohol is a good cleaning fluid to use, but soap and water will also work. These sections should be completely clean and dry to ensure that the double-sided tape on the bracket will adhere well.
  6. Remove the backing on the double sided tape on the horizontal section of each bracket, and carefully align the license plate and bracket assembly once again on the front of your bumper. Press the bracket upwards against the bumper and hold it firmly in place for about 30 seconds to ensure good adhesion.
  7. Using the included 7/64″ drill bit, drill a small hole in the bottom of the bumper through the center of the existing hole in each horizontal bracket section.
  8. With a Phillips screwdriver, secure the bracket to the underside of your bumper using the supplied stainless steel pan-head self-tapping screws. It is important to use these screws, as the double side tape alone may not provide sufficient grip under some conditions.
  9. Readjust the license plate angle if necessary, and tighten the angle adjustment screws.
  10. Tighten the 4 license plate mounting screws.

Your license plate bracket is now installed!

How To Install Front License Plate Bracket On Ford Edge Titanium

Got questions about the installation? Send us a note at bracket-support@skenedesign.com.